This is a good used set of steel rims and Carlisle tires from a John Deere 1032 snowblower.
This is a good used set of steel rims and Carlisle tires from a John Deere 1032 snowblower.
This is a good used set of steel rims and Carlisle tires from a John Deere 1032 snowblower.
This one is a survivor that is in good condition for it’s age! And a good piece of John Deere history to a collector. This machine was built by Jacobson, it is a 2cycle 32.1 mix, the electric start still works. I used this machine as a antique engine display unit in shows and to my knowledge has not been put in service blowing snow in about 20 yrs. It does have a small crack in one of the bolt holes in the plastic on the cover (see picture). It does start up and run when you shoot gas in it, but should have new gaskets and seals put in the carburetor if to be put back in service, especially not being used in 2 decades. The items description is listed to my knowledge and the best of my ability. All sales are final. What you see in the picture of the machine is what you wil receive.
TWO John Deere TIRE RIM WHEEL assemblies 13×5.00-6 for some Garden Tiller Snow Blower Thrower with 3/4 ID shaft. Your assemblies will arrive aired up and ready to mount on your axle. Please read the add fully and see pictures top of page before you ask questions as we have detailed information in the description about this product. Does not fit all models! These are DIRECTIONAL (1)RIGHT / (1)LEFT Assemblies (SEE PICTURES). Part Numbers: 86151-L and 86151-R. BRAND: Kenda SIZE: 13×5.00-6 TREAD: A-478 Traction. DESCRIPTION: 2ply (load range “A”) Tube-Less R-1 Tiller / Snow blower Tire NHS. Height: 12.8 inches Width: 5.0 inches Rim Diameter: 6 inch. Weight Capacity: 295 lbs. NOTE: NHS This tire a N on H ighway S ervice Tire. BRAND: Monitor (MADE IN THE U S A) Rim Size: 6 x 4.375. Rim Diameter: 6 ” Rim Width: 4.375 “. One piece Welded Steel / Drive Axle /. Center Hole Opening: 3/4 (uses 3/4 inch shaft or axle) {see picture above}. Shaft Length: 5.25 over all SHAFT length measured through the center of the rim; shaft end to shaft end. Dowel hole size: 0.25 Shaft Offset: {see picture above}. AMOUNT OF SHAFT sticking out {each side of rim}. Outside of Rim: valve stem side – 1.25 inch {see picture above}. Inside of Rim: towards the frame of mower 3.50 inches {see picture above}. The remaining portion of the shaft is between the two halves of the rim, giving this type rim superior strength and stability. Original Equipment applications include: John Deere. Troy, Snapper, Arens, Murray. Toro, Bobcat, Brunton, MTD, Ditch Witch and many other brand Mowers, Tillers and Trenchers and Snow blowers. Carter Brothers, Roketa, Helix and other brand GO KARTS and many other LIVE AXLE TYPES EQUIPMENT used in various industrial applications. CUSTOM BUILDERS AND ALL DEALERS WELCOME.
OEM John Deere Part Number M135649 Replaces Prior MPN M94975 M122371 M119749 Compatibile With: John Deere: X530 Multi-Terrain Series, X534 Multi-Terrain Series, X540 Multi-Terrain Series, X580, X584, X590 Multi-Terrain Series, X710 Signature Series, X730 Signature Series, X734 Signature Series, X738 Signature Series, X739 Signature Series, X750 Signature Series, X754 Signature Series, X758 Signature Series, X940 Signature Series, X948 Signature Series, X949 Signature Series, X950R. John Deere M135649 Blower Scraper Blade X 530 540 710 730 750 758 940 948. OEM John Deere Part Number M135649 Replaces Prior MPN M94975 M122371 M119749 Compatible with the following models: John Deere: X530 Multi-Terrain Series, X534 Multi-Terrain Series, X540 Multi-Terrain Series, X580, X584, X590 Multi-Terrain Series, X710 Signature Series, X730 Signature Series, X734 Signature Series, X738 Signature Series, X739 Signature Series, X750 Signature Series, X754 Signature Series, X758 Signature Series, X940 Signature Series, X948 Signature Series, X949 Signature Series, X950R Please Refer to Original Equipment Owners Manual to verify Compatibility. This product is brand new and will come in original factory packaging. We are proud to be a factory authorized retailer. We use several different carriers and choose the most economical for the item and destination based on the estimated transit time displayed.
This is the tallest, third generation chute and deflector assembly from an Ariens snowblower. It measures 25 max height at full deflector extension. I have a pic that displays the different Ariens chutes, this is the tallest one. You would need to zip a few welds to remove the original base mount, and then ATTACH THE ORIGINAL BASE GEAR FROM YOUR MACHINE. I have a few of these base gears available also. This will allow the chute assembly to fit the Ariens 924 series, as well as the old style John Deere 726, 826, 832, and 1032 machines. Parts are all in good used condition and ready to work.
This is a nice used auger pulley/hub assembly from a John Deere 924DE snowblower.
John Deere 318,322,332 Quick-Tack (Quick Hitch) for 46 or 47 snow blower/ Stop & Driveshaft kit BM18172, which is no longer available new from John Deere. This part number driveshaft is also used for quick attach 46 or 47 snowblowers use on models 420 and 430. According to John Deere this drive shaft can also be used for quick attach 46 and 47 snowblowers and 51 front brooms on front mount mower models F910, F911, F915, F925, F930, F932 and F935. Please verify if this will work for you. Parts were never used, but do have scuff marks, and nicks from being moved around in the box.
Fits models: LX172 LX173 LX176 LX178 LX186 LX188 GT242 GT262 GT275 More Replaces AM115124 and AM115813, AM132775, AM131461 and AM132776.
Used John Deere am35456 gear case. Fits 46, 50 Snowthrowers on 400,420,430 garden tractors. Good shape, turns smooth, minimal backlash. Look at pics, what you see is what you get.